PCB-(M)260A12
- Triaxial force sensor with charge output,
- Measuring range (Z axis) 4.45 kN,
- Measuring range (X - and Y-axes) 4.45 kN,
- Sensitivity (Z-axis) 3.4 pC/N,.
- Sensitivity (X - and Y-axes) 7.2 pC/N,.
- Upper frequency limit 90,000 Hz,.
- Three 10-32 connectors on the side
| basic data | |||
| Sensitivity (X- and Y-axis) (± 15%) | 32 pC / lb | 7.19 pC / N | [1] |
| Sensitivity (Z-axis) (± 15%) | 15 pC / lb | 3.37 pC / N | [1] |
| Measurement range (Z axis) | 1,000 lb | 4.45 kN | |
| Measurement range (X- and Y-axis) | 1,000 lb | 4.45 kN | |
| Maximum force (Z-axis) | 1,320 lb | 5.87 kN | |
| Maximum force (X- and Y-axis) | 1,000 lb | 4.45 kN | |
| Maximum torque (Z-axis) | 40 ft-lb | 54.23 Nm | |
| Maximum torque (X- and Y-axis) | 70 ft-lb | 94.91 Nm | |
| Upper limit frequency | 90,000 Hz | ||
| linearity error | ≤1% FS | [2] | |
| Crosstalk (between X and Y-axis) | ± 3% | ||
| Crosstalk (between X / Y-axis and Z-axis) | ± 5% | ||
| Operating conditions | |||
| temperature range | -100 ... 350 ° F | -73 ... 177 ° C | |
| Technical characteristics | |||
| capacity (all axes) | 30 pF | [3] | |
| Insulation resistance (all axes) | ≥1.000.000 MΩ | ||
| Output polarity (in the direction of the markings) | negative | ||
| physical properties | |||
| preload | ?10.000 lb | ?44,48 kN | [4] |
| Stiffness (Z-axis) | 19 lb / microinches | 3.3 kN / micron | [3] |
| Stiffness (X- and Y-axis) | 6 lb / microinches | 1 kN / micron | [3] |
| Size - Height | 0.390 in | 9,90 mm | |
| Size - Length | 1.25 in | 31.8 mm | |
| Size - Width | 1.25 in | 31.8 mm | |
| Size - inside diameter | 0.512 in | 13 mm | |
| Size - diameter of the measuring surface | 0.920 in | 23.37 mm | |
| Dimensions | 1.5 oz | 42.5 grams | |
| housing material | stainless steel | ||
| seal | hermetically sealed | ||
| electrical connection | Three 10-32 coaxial sockets | ||
| port location | Laterally | ||
| Hints | |||
| [1] | When the recommended preload. The sensitivities can change by ± 5%, depending on the used preload. | ||
| [2] | Zero-based line of best fit, determined by the method of least squares | ||
| [3] | typically, | ||
| [4] | The pre-load should be at least ten times the operating range used on the X and Y-axis. | ||
| included supply | |||
| 081A74 | Vorlastbolzen (for models 260A02, 260A12, and 260A32) | -1 | |
| 082M12 | Washer (for models 260A02, 260A12, and 260A32) | -1 | |
| 083A13 | Mounting sleeve (for models 260A02, 260A12, and 260A32) | -1 | |
| (W) Waterproof cable connection | |||
| cable outlet | Laterally | ||
| (M) Metric assembly | |||
| included supply | |||
| M081A74 | mounting bolts |
PCB-(M)260A12
