PCB-3501A2060KG
zoom_out_map

PCB-3501A2060KG

  • MEMS high shock sensor,
  • Measuring range 60,000 g,
  • Sensitivity 0.0003 mV / g,
  • Frequency range 0 … 20,000 Hz,
  • Surface mount
  • basic data
    sensitivity (at 10 V DC supply voltage) (±50%) 0.003 mV / g 0.0003 mV/(m/s²) [2]
     
    sensitivity 0.0003 mV / V / g 0,00003 mV/V/(m/s²) [6]
     
    Range ±60. 000 g ±588. 400 m/s² pk  
     
    frequency range (1 dB) 0 … 20,000 Hz    
     
    Resonance frequency > 120,000 Hz    
     
    damping rate 2% crit chance   [1]
     
    Linearity error ≤1%    
     
    transverse acceleration sensitivity ≤3%    
    conditions
    Ü berlastlimit (shock) ±100. 000 g pk ±980. 665 m/s² pk [3]
     
    Ü berlastlimit (mechanical stop) ≥80,000 g ? 782.534 m/s² pk  
     
    temperature range (operation) -.-65 … 250 ° F -54 … 121 ° C  
     
    Temperature coefficient of sensitivity -0.11 %/°F -0.20 %/°C [1]
     
    Max. Temperature dependent offset shift ±10 mV   [4]
     
    strain sensitivity (base area) 0,3 g/µε 2.94 (m/s²)/µε [1]
    Technical
    supply voltage (max) 15.0 V DC    
     
    power < 3 mA    
     
    input impedance (kΩ ±2) 6,000Ω   [2]
     
    output impedance (kΩ ±2) 6,000Ω   [2]
     
    Spannungsoffset 40 … 40 mV DC   [2]
     
    settling time 0.01 s   [5]
    Physical properties
    Sensor element Piezoresistive MEMS element    
     
    Geometry of the sensor element Active bridge circuit    
     
    Housing material Ceramic    
     
    Waterproofing epoxy resin    
     
    size - height 0,085 in 2,16 mm  
     
    Gr öße - length 0,236 in 6.00 mm  
     
    size - width 0,138 in 3.50 mm  
     
    mass 0.005 oz 0.15 grams [1]
     
    electrical connection soldering connection surfaces for SMT assembly    
     
    mounting surface mount (SMT)    
    Notes
    [1] typically    
     
    [2] Pro sensor tested and documented on calibration certificate supplied with    
     
    [3] a half-sine pulse ≤ 20 µs    
     
    [4] -54 … 121 ° C, reference 24 ° C    
     
    [5] settling time is zero on ±2 at the time, the maximum needed the sensor signal, after the supply voltage is applied to approximate % of the output span.The mounting surface must be located in the thermal balance.    
     
    [6] Temperature coefficient of sensitivity is proportional to the applied supply voltage and can use a different voltage than at the calibration (10 V DC) ) are calculated from the calibration data. The possible measurement error increases with minimal (around0.5%).    
    Accessories
    ACS-62 calibration of Piezoresistive shock sensors -1  
    PCB-3501A2060KG

    Specific References

    Download

    3501A2060KG_drawing.PDF

    Technical drawing

    Download (598.33k)

    3501A2060KG_manual.PDF

    Operating instructions

    Download (1.1M)

    3501A2060KG_specs.PDF

    Technical data sheet

    Download (438.54k)