PCB-(M)607A01
| basic data | |||
| sensitivity (±15%) | 100 mV/g | 10.2 mV/(m/s²) | [6] |
| measuring range | ±50 g | ±490 m / s² | |
| Frequency range (± 3 dB) | 30 … 600,000 cpm | 0.5 … 10,000 Hz | |
| resonance frequency | 1,080 kcpm | 18,000 Hz | [1] |
| Wide band resolution | 350 µg | 3.434 µm / s ² | [1] |
| linearity | ≤1% | [2] | |
| Lateral acceleration sensitivity | ≤ 7% | ||
| Conditions of use | |||
| Overload limit (shock) | 5,000 g pk | 49,050 m/s² pk | |
| Temperature range | -65 … 250 ° F | -54 … 121 ° C | |
| protection class | IP68 | ||
| technical characteristics | |||
| Settling time (on bias voltage ± 1%) | ≤ 2.0 s | ||
| discharging charging time constant | ≥ 0.3 s | ||
| Power | 18 … 28 V DC | ||
| constant power supply | 2 … 20 mA | ||
| Output impedance | < 150 Ω | ||
| Bias voltage | 8 … 12 V DC | ||
| Spectral noise (10 Hz) | 8 µg / √ Hz | 78.5 (µm / s ²) / √ Hz | [1] |
| spectral noise (100 Hz) | 5 µg / √ Hz | 49.1 (µm / s ²) / √ Hz | [1] |
| spectral noise (1,000 Hz) | 4 µg / √ Hz | 39.2 (µm / s ²) / √ Hz | [1] |
| electric Insulation (housing) | ≥ 100 MΩ | ||
| physical properties | |||
| size - hex | 7/8 in | 22 mm | |
| size ße - height | 1.23 in | 31.2 mm | |
| mass | 3.7 oz | 105 grams | |
| fixing | mounting bolt | ||
| Mounting thread | ¾-16 female thread | noEquivalent | [3] |
| Assembly torque (mounting bolts) | 7 … 8 ft-lb | 9.5 … 10.8 Nm | [4] [5] |
| Assembly torque (hex nut ) | 2 … 5 ft-lb | 2.7 … 6.8 Nm | |
| sensor element | ceramic | ||
| geometry of the sensor element | shear principle | ||
| Housing material | stainless steel | ||
| sealing | hermetically sealed welded | ||
| Electrical connection | 2-pin connector (MIL-C-5015) | ||
| connection position | side | ||
| notes | |||
| [1] | typically | ||
| [2] | zero-based balancing line, determined using the method of least squares | ||
| [3] | no equivalent in SI units | ||
| [4] | Assembly requires Allen key 1/8 "(for inch mounting bolts) or 3 mm (for metric mounting bolts). | ||
| [5] | of the mounting boltsmust be tightened with a higher torque than the hex nut, so that the sensor can easily be removed. | ||
| [6] | conversion factor 1 g = 9.81 m/s² | ||
| [7] | details: see PCBs Declaration of conformance PS023 and < a href = ""... "/ produkte_skript/downloads/ce/ps060.pdf" "class ="blue"> PS060 | ||
| equipment | |||
| 080A162 | mounting bolt ¾-16 on 1/4"-28 | -1 | |
| ICS-2 | single point calibration at 100 Hz (traceable to NIST) | -1 | |
| (M) metric mounting | |||
| equipment | |||
| M080A163 | mounting bolts M6 x ¾-16 1 | -1 | |
| (TO) temperature output | |||
| temperature range | 36 … 250 ° F | 2 … 121 ° C | |
| Transcription factor | 5.56 mV / ° F (zero point at 32 °F) | 10 mV / ° C | |
| electrical connection | 3-Pin MIL-C-5015 | ||
| Pin assigNment (PIN A) | acceleration output | ||
| Pin assigNment (PIN B) | dimensions | ||
| pin assigNment (PIN C) | temperature output | ||
| (EX) with ATEX approval | |||
| Approved for use in potentially explosive atmospheres | ExIA IIC T4, AExia IIC, T4 | ||
| approval for use in potentially explosive atmospheres | EEx nL IIC T4, 40 ° C ≤ Ta ≤ 121 ° C, II 1 G | ||
| approval for use in potentially explosive atmospheres | CL I, div I, groups A, B, C, D CL II, div I, groups E, F, G Cl III, div I | ||
| Approval for use in potentially explosive atmospheres | CL I, div 2, groups A, B, C, D ExnL IIC T4, AExnA IIC T4 | ||
| approval for hazardous Atmospheres | EEx nL IIC T4,-40 ° C ≤ Ta ≤ 121 ° C, II 3 G |
PCB-(M)607A01
