This website uses cookies, which are necessary for the technical operation of the site and which are always set. In order to further improve our offer and our website, we would like to set additional cookies in order to collect anonymized data for statistics and analyzes. However, these are only set with your consent. Further information on cookies can be found in our privacy policy.

Privacy policy Acceptdone
    PCB-(M)603C01
    zoom_out_map

      PCB-(M)603C01

    • Industrial ICP® vibration sensor,
    • Measurement range 50 g,
    • Sensitivity 100 mV/g,
    • Frequency range 0.5 … 10,000 Hz,
    • One-point calibration at 100 Hz,
    • 2-pin female connector above
      • basic data
      sensitivity (±10%)100 mV/g10.2 mV/(m/s²)[5]
      measuring range±50 g±490 m / s²
      Frequency range (± 3 dB)30 … 600,000 cpm0.5 … 10,000 Hz[1]
      resonance frequency1,500 kcpm25,000 Hz[2]
      Wide band resolution350 µg3.434 µm / s ²[2]
      linearity≤1%[3]
      Transverse acceleration sensitivity≤ 7%
      conditions of use
      Overload limit (shock)5,000 g pk49,050 m/s² pk
      temperature range-65 … 250 ° F-54 … 121 ° C
      Type of protectionIP68
      Technical characteristics
      settling time (on bias voltage ± 1%)≤ 2.0 s
      discharging charging time constant≥ 0.3 s
      Power18 … 28 V DC
      constant power supply2 … 20 mA
      Output impedance< 150 Ω
      Bias voltage8 … 12 V DC
      Spectral noise (10 Hz)8 µg / √ Hz78.5 (µm / s ²) / √ Hz[2]
      spectral noise (100 Hz)5 µg / √ Hz49.1 (µm / s ²) / √ Hz[2]
      Spectral noise (1,000 Hz)4 µg / √ Hz39.2 (µm / s ²) / √ Hz[2]
      electrical insulation (housing)≥ 100 MΩ
      Physical properties
      size - Allen11/16 in18 mm
      size - height1.65 in42.2 mm
      Size1.8 oz51 grams
      mounting thread1/4 "-28 threadedNo metric equivalent"[4]
      Assembly torque2 … 5 ft-lb2.7 … 6.8 Nm
      sensor elementceramic
      geometry of the Sensor elementshear principle
      housing materialstainless steel
      sealinghermetically sealed welded
      Electrical connection2-pin connector (MIL-C-5015)
      connection positionabove
      notes
      [1]the upper cut-off frequency tolerance: ±10%
      [2]typically
      [3]zero-based balancing line, determined using the method of least squares
      [4]no equivalent in SI units
      [5] Conversion factor 1 g = 9.81 m/s²
      [6]details: see PCBs Declaration of conformance PS023 and PS060
      Equipment
      081A40mounting boltswith 1/4 "-28 thread-1
      ICS-2single point calibration at 100 Hz (traceable to NIST)-1
      (M) metric mounting
      " Accessories
      M081A61metric mounting bolts with M6 thread-1
      (TO) temperature output
      Temperature range36 … 250 ° F2 … 121 ° C
      transcription factor5.56 mV / ° F
      (zero point at 32 °F)      		10 mV / ° C
      Electrical connection3-Pin MIL-C-5015
      pin assigNment (PIN A)acceleration output
      pin assigNment ( PIN B)ground
      pin assigNment (PIN C)temperature output
      size - height1.86 in47.2 mm
      Mass2.0 oz56.7 grams
      (EX) with ATEX approval
      approval for use in potentially explosive atmospheresCL I, div 2, groups A, B, C, D
      ExnL IIC T4, AExnA IIC T4
      PCB-(M)603C01

      Specific References

      Download

      603C01_drawing.PDF

      Technical drawing

      Download (59.19k)

      603C01_manual.PDF

      Operating instructions

      Download (888.34k)

      603C01_specs.PDF

      Technical data sheet

      Download (81.65k)