PCB-350B42
- Triaxial ICP® shock acceleration sensor
- Mass insulated
- With electrical and mechanical filter
(-3 dB at 17,000 Hz) - Measuring range 50,000 g
- Sensitivity 0.1 mV / g
- Frequency range 4 ... 10,000 Hz
- Integrated connection cable, length 1.5 meters,
ending on a 4-pin connection socket - Including extension cable, length 1.5 meters,
ending on three BNC plugs
| Specifications | |||
|---|---|---|---|
| Basic data | English units | SI units | |
| Sensitivity (± 30%) | 0,1 mV/g | 0,01 mV/(m/s²) | |
| Measuring range | ± 50,000 g pk | ±440.000 m/s²pk | |
| Frequency range (± 1 dB) | 4 … 10.000 Hz | ||
| Resonance frequency | >50.000 Hz | ||
| Corner frequency of the electrical filter (3 dB) | 17.000 Hz | [1][2] | |
| Resonance frequency of the mechanical filter | 35.000 Hz | [1][3] | |
| Broadband resolution (1 ... 10,000 Hz) | 0,5 gRMS | 4,9 m/s²RMS | [1] |
| Linearitätsfehler | ≤2,5 % | ||
| Lateral acceleration sensitivity | ≤7 % | ||
| Conditions of use | |||
| Overload limit (shock) | ± 150,000 g pk | ±1.471.500 m/s²pk | |
| Temperature range (operation) | -10 … 150 °F | -23 … 66 °C | |
| Temperature range (storage) | -40 … 200 °F | -40 … 93 °C | |
| Stretch sensitivity (base area) | 0.002 g / ml | 0.02 (m / s²) / ε | [1] |
| Technical characteristics | |||
| Supply voltage | 20 … 30 VDC | ||
| Constant current supply | 2… 20 mA | ||
| Output impedance | ≤200 Ω | ||
| Bias voltage | 8 … 14 VDC | ||
| Discharge time constant | 0,1 s | [1] | |
| Settling time (to bias voltage ± 10%) | <1 s | ||
| Electrical insulation (base) | >100 MΩ | ||
| Physical characteristics | |||
| Sensor element | Ceramics | ||
| Geometry of the sensor element | Scherprinzip | ||
| Housing material | Titan | ||
| seal | Hermetically sealed | ||
| Size - height | 1,02 in | 26,0 mm | |
| Size - length | 1,02 in | 26,0 mm | |
| Size - width | 1,02 in | 26,0 mm | |
| Mass (without cable) | 0.95 oz | 27 grams | [1] |
| Cable outlet | Laterally | ||
| Cable termination | 4-pin socket (1/4 "-28) | ||
| Cable length | 5,0 ft | 1,52 m | |
| Cable type | Type 034, shielded 4-wire cable | ||
| Attachment | Through holes | ||
| Hints | |||
|---|---|---|---|
| [1] | Typically | ||
| [2] | Second order low pass filter | ||
| [3] | The amplitude is increased by 9 dB in the range of the resonance frequency. | ||
| [4] | Shaker test at 100 Hz | ||
| [5] | Details: siehe PCB Declaration of Conformance PS023 | ||
| included supply | ||
|---|---|---|
| 034G05 | Shielded 4-wire cable, length 1.5 meters, 4-pin connector on three BNC connectors | (1) |
| 100-16040-40 | Mounting screw M6 x 1.0 | (2) |
| 100-6774-10 | Mounting screw 1/4 "-28 | (2) |
| 100-8994-40 | Grease | (1) |
| ACS-14T | Hopkinson bar calibration for shock transducers | (1) |
| ACS-22T | Frequency response for triaxial transducers, traceable to NIST (100 Hz up to the upper ± 1dB point | (1) |
PCB-350B42
