PCB-S112A22
High resolution ICP® pressure probe, 50 psi, 100 mV/psi, 0.218" dia. diaphragm, accel. comp., stainless diaphragm
- Measurement Range: 50 psi (345 kPa)
- Sensitivity: (±15%)100 mV/psi (14.5 mV/kPa)
- Low Frequency Response: (-5%)0.50 Hz
- Resonant Frequency: >=250 kHz (>=250 kHz)
- Electrical Connector: 10-32 Coaxial Jack
- Weight: 0.21 oz (6.0 gm)
Specification Notes
[1] Zero-based, least-squares, straight line method.
[2] Typical value.
[3] For +10 volt output, minimum 24 VDC supply voltage required. Negative 10 volt output may be limited by output bias.
[4] See PCB Declaration of Conformance PS023 for details.
| English: | SI: | ||
|---|---|---|---|
| Performance | |||
| Measurement Range (for ±5V output) | 50 psi | 345 kPa | |
| Useful Overrange (for ± 10V output) | 100 psi | 690 kPa | [3] |
| Sensitivity (±15 %) | 100 mV/psi | 14.5 mV/kPa | |
| Maximum Pressure (step) | 500 psi | 3450 kPa | |
| Maximum Pressure (Total) | 15000 psi | 103421 kPa | |
| Resolution | 0.1 mpsi | 0.000689 kPa | [2] |
| Resonant Frequency | ≥250 kHz | ≥250 kHz | |
| Rise Time (Reflected) | ≤2.0 µ sec | ≤2.0 µ sec | |
| Low Frequency Response (-5 %) | 0.50 Hz | 0.50 Hz | |
| Non-Linearity | ≤1.0 % FS | ≤1.0 % FS | [1] |
| Environmental | |||
| Acceleration Sensitivity | ≤0.002 psi/g | ≤0.0014 kPa/(m/s²) | |
| Temperature Range (Operating) | -100 to +275 °F | -73 to +135 °C | |
| Temperature Coefficient of Sensitivity | ≤0.06 %/°F | ≤0.108 %/°C | |
| Maximum Flash Temperature | 3000 °F | 1650 °C | |
| Maximum Vibration | 2000 g pk | 19613 m/s² pk | |
| Maximum Shock | 20000 g pk | 196133 m/s² pk | |
| Electrical | |||
| Output Polarity (Positive Pressure) | Positive | Positive | |
| Discharge Time Constant (at room temp) | ≥1.0 sec | ≥1.0 sec | |
| Excitation Voltage | 22 to 30 VDC | 22 to 30 VDC | |
| Constant Current Excitation | 2 to 20 mA | 2 to 20 mA | |
| Output Impedance | <100 Ohm | <100 Ohm | |
| Output Bias Voltage | 8 to 14 VDC | 8 to 14 VDC | |
| Physical | |||
| Sensing Geometry | Compression | Compression | |
| Sensing Element | Quartz | Quartz | |
| Housing Material | 17-4 Stainless Steel | 17-4 Stainless Steel | |
| Diaphragm | Invar | Invar | |
| Sealing | Welded Hermetic | Welded Hermetic | |
| Electrical Connector | 10-32 Coaxial Jack | 10-32 Coaxial Jack | |
| Weight (with clamp nut) | 0.21 oz | 6.0 gm | |
* All specifications are at room temperature unless otherwise specified.
Accessories
| Supplied | ||
| 060A03 | Clamp nut, 5/16-24-2A thd, 1/4" hex, SS (for Series 111, 112 & 113) | 1 |
| 060A05 | Clamp nut, M7 x 0.75-6G thd (for Series M111, M112 & M113) | 1 |
| 065A05 | Seal sleeve, sensor recess mount, 0.248" OD x 0.221" ID x 0.240" thk, 17-4 SS (for Series 111A, 112A & 113A) | 1 |
| 065A02 | Seal ring, sensor flush mount, 0.248" OD x 0.219" ID x 0.015" thk, brass (for Series 111A, 112A & 113A) | 3 |
Optional Versions
(E) Emralon coating
| English | SI | |
|---|---|---|
| Electrical Isolation | 100000000 Ohm | |
| Coating | Emralon | |
(J) Ground Isolated
| English | SI | |
|---|---|---|
| Electrical Isolation | 100000000 Ohm | 100000000 |
(S) Stainless Steel Diaphragm
| English | SI | |
|---|---|---|
| Diaphragm | 316L Stainless Steel | |
(W) Water Resistant Cable
| Accessories: | |||
|---|---|---|---|
| Supplied | 060A03 | Clamp nut, 5/16-24-2A thd, 1/4" hex, stainless steel | 1 |
(WM) Water Resistant Cable
| Accessories: | |||
|---|---|---|---|
| Supplied | 060A05 | Clamp nut M7 x 0.75-6g thd | 1 |
PCB-S112A22
