PCB-483C28
| basic data | |||
| number channels | 8 | ||
| sensor type | ICP, voltage, bridge / differential signal | ||
| Accuracy (amplification factor 0, 1 x 0, 4 x) | ≤5% | ||
| accuracy (amplification factor 0, 5 x to 0, 99 x | ≤1% | ||
| ) | |||
| Accuracy (amplification factor 1, 0 x 2000 x) | ±0, 5% | ||
| accuracy (sensor power supply) | ≤1% | ||
| Input range (differential signal) | ±0. … 10 V | ||
| (minimum) output range | ±10 V | ||
| frequency range (amp ärkungsfaktor 100 x) (-5%) | 0.05 … 100,000 Hz | [1] | |
| frequency range (amplification factor ≥ 100 x) (-5%) | 0.05 … 50,000 Hz | [1] | |
| Phase shift (at 1,000 Hz) | ±1 ° | ||
| crosstalk (maximum, at 10,000 Hz) | -72 dB | ||
| Shunt calibration | internal/external | ||
| TEDS reader function | Yes | ||
| displayBias voltage/error (via LEDs) | Open circuit/short circuit/overload | ||
| digital interface | |||
| digital interface | Ethernet | ||
| Conditions of use | |||
| Temperature range (operation) | 32 … 120 ° F | 0 … 50 ° C | |
| Technical properties | |||
| Power supply | voltage | ||
| Voltage (47 … 63 Hz) | 100 … 240 V AC | ||
| power | ≤ 0.9 A | ||
| Supply voltage (for ICP® sensors) | > 24 V DC | ||
| constant power supply (for ICP®-) Sensors) | 0 … 20 mA | ||
| supply voltage (for other passive sensors, plus pole) | 0 … 12 V | [4] | |
| power supply (for other passive sensors, negative pole) | 0 …-12 V | 0 …-12 V | [4] [5] |
| Asymmetry compensation (maximum, amplification factor < 10 x) (for other passiveSensors) | ±2 V | ||
| asymmetry compensation (maximum, gain ≥ 10 x) (for other passive sensors) | ±0, 2 V | ||
| Asymmetric voltage (max) | ±10 V | ||
| Influence of temperature on DC offset (max) | 5 µV / ° C | ||
| DC offset (AC coupled) | ≤ 50 mV | ||
| DC offset (DC coupled, gain100 x) | < 10 mV | ||
| DC offset (DC coupled, gain ≥ 100 x) | < 20 mV | ||
| Maximum power consumption (for other passive sensors) | 30 mA | ||
| output impedance | ≤ 50 Ω | ||
| (input impedance ) | > 1 M Ω | ||
| 10 V pk | Overload threshold (±0. 2 V pk) | ||
| wide band noise (amplification factor 1 x) (1 … 10,000 Hz) | 50 µV rms | [3] | |
| spectral noise (amplification factor 1 x) (1 Hz) | 6.0 µV / √ Hz | [3] | |
| SpectralNoise (amplification factor 1 x) (10 Hz) | 1.5 µV / √ Hz | [3] | |
| spectral noise (amplification factor 1 x) (100 Hz) | 1.0 µV / √ Hz | [3] | |
| Spectral noise (amplification factor 1 x) (1,000 Hz) | 1.0 µV / √ Hz | [3] | |
| spectral noise (amplification factor 1 x) (10,000 Hz) | 1.0 µV / √ Hz | [3] | |
| wide band noise (amplification factor 10 x) (1 … 10,000 Hz) | 75 µV rms | [3] | |
| spectral noise ( Gain 10 x) (1 Hz) | 20 µV / √ Hz | [3] | |
| spectral noise (amplification factor 10 x) (10 Hz) | 1.5 µV / √ Hz | [3] | |
| Spectral noise (10 x gain) (100 Hz) | 1.0 µV / √ Hz | [3] | |
| spectral noise (10 x gain) (1,000 Hz) | 1.0 µV /. √ Hz | [3] | |
| spectral noise (10 x gain) (10,000 Hz) | 1.0 µV / √ Hz | [3] | |
| wide band noise (Verstä rkungsfaktor 100 x)(1 … 10,000 Hz) | 350 µV rms | [3] | |
| spectral noise (gain 100 x) (1 Hz) | 140.0 µV / √ Hz | [3] | |
| spectral noise (100 x gain) (10 Hz) | 14.0 µV / √ Hz | [3] | |
| spectral noise (gain x 100) (100 Hz) | 8.0 µV / √ Hz | [3] | |
| spectral noise (100 x gain) (1,000 Hz) | 4.0 µV / √ Hz | [3] | |
| spectral noise (gain x 100) (10,000 Hz) | 4.0 µV / √ Hz | [3] | |
| wide band noise (amplification factor 1000 x) (1 … 10,000 Hz) | 3,000 µV/rms | [2] | |
| physical properties | |||
| electrical connection (ICP® sensor input) | BNC socket | ||
| Electrical connection (bridge / differential signal) | 8-pin mini DIN socket | ||
| electrical connection (output) | BNC Jack | ||
| Electrical connection (Ethernet) | RJ45 | ||
| Größe - height (nominal) | 1.75 in | 44.5 mm | |
| size - width (nominal) | 19.0 in | 482.6 mm | |
| size - depth ( nominal) | 13.7 in | 348 mm | |
| mass | 7.0 lb | 3.18 kg | |
| notes | |||
| [1] | AC coupled (lower limiting frequency at coupling: 0 Hz) | ||
| [2] | coupled with 350-Ω bridge (bridge / differential signal) | ||
| [3] | typically, AC coupled | ||
| [4] | can be set in steps of 0.1 V | ||
| [5] | potential of the minus pole is equal to 0 V (unipolar supply) or corresponds to the inverted Potential of the positive terminal (bipolar supply). | ||
| [6] | details: see PCBs Declaration of conformance PS023 | ||
| supplied accessories ör | |||
| 017AXX | cord | -1 | |
| EE75 | Configuration software "MCSC" | -1 |
PCB-483C28
