PCB-111A24
of
| basic data | |||
| measuring range (±5 V output range) | 1,000 psi | 6.895 kPa | |
| usable range (output range ±10 V) | 2,000 psi | 13.790 kPa | [2] |
| sensitivity (±0, 5 mV / psi) | 5.0 mV / psi | 0.73 mV / kPa | |
| maximum static pressure | 10,000 psi | kPa 68.950 | |
| resolution | 0,02 psi | 0.14 kPa | |
| resonance frequency | ≥400,000 Hz | ||
| Rise time (reflected pressure) | ≤ 1.5 µs | ||
| lower limiting frequency (-5%) | 0.005 Hz | ||
| linearity error | ≤2.0% FS | [1] | |
| conditions | |||
| acceleration sensitivity | ≤ 0.002 psi/g | >0,0014 kPa/(m/s²) | |
| temperature range ( Operation) | -100 … 275 ° F | -73 … 135 ° C | |
| Temperature coefficient of sensitivity | ≤0,2 %/°F | ≤0.06 %/°C | |
| maximum temperature shock(for fraction of a second) | 3,000 ° F | 1.649 ° C | |
| Maximum acceleration | 2,000 g pk | 19.614 m/s² pk | |
| Maximum shock resistance | 20,000 g pk | 196.140 m/s² pk | |
| technical Properties | |||
| output polarity (positive pressure) | positive | ||
| discharging charging time constant (at room temperature) | ≤100 Ω | ||
| Supply | 20 … 30 V DC | ||
| constant power supply | 2 … 20 mA | ||
| Output impedance | ≤100 Ω | ||
| Bias voltage | 8 … 14 V DC | ||
| Physical properties | |||
| Geometry of the sensor element | compression principle | ||
| Sensor element | quartz | ||
| Housing material | 17-4 (Stainless steel) | ||
| membrane | INVAR | ||
| waterproofing | epoxy resin | ||
| Electrical connection | 10-32-coaxial socket | ||
| weight | 0.21 oz | 6 g | |
| notes | |||
| [1 ] | zero-based balancing line, determined using the method of least squares | ||
| [2] | for output range up to 10 V, the supply voltage must at least 24 V DC is. At low bias voltage of the sensor, no negative output range is usable up to-10 V. | ||
| [3] | details: see PCBs Declaration of conformance PS023 | ||
| equipment | |||
| 060A03 | installation sleeve, 5 /. 16-24-2A thread, 1/4 "hex, (stainless steel) | -1 | |
| 060A05 | installation sleeve, M7 x 0.75-6 g-thread | -1 | |
| 065A02 | sealing ring f for flush mounting, 0,248 "outside x 0.219" x 0.015 "tall, brass | 3 | |
| 065A05 | gasket spacer, 0,248 "outside x 0,221" x 0.240 "high, 17-4 (Stainless steel) | -1 | |
| (S) Emralon coating | |||
| coating | Emralon | ||
| electrical insulation | >100 MΩ | ||
| equipment | |||
| 065A22 | seal, 0.250 "x outside 0,218" x 0.015 "high, Torlon or Vespel | 3 | |
| 065A08 | insulation ring, 0.250 "x outside 0,218" x 0.027 "high, anodized aluminium | 3 | |
| (S) stainless steel diaphragm | |||
| membrane | 316 L ( Stainless steel) |
PCB-111A24
