PCB-(M)260A01
| basic data | |||
| sensitivity (Z axis) (±20%) | 2.5 mV / N | lb/0.56 mV / N | [2] [3] |
| sensitivity (X - and Y-axes) (±20%) | 10 mV / lb | 2.25 mV / N | [2] [3] |
| measuring range (Z axis) | 1,000 lb | 4.45 kN | |
| measuring range (X - and Y-axes) | 500 lb | 2.22 kN | |
| Maximum power (Z axis) | 1,320 lb | 5.87 kN | |
| maximum force (X - and Y-axes) | 660 lb | 2,94 kN | |
| maximum moment (Z axis ) | 14 ft-lb | 18.98 Nm | |
| maximum moment (X - and Y-axes) | 13 ft-lb | 17,63 Nm | |
| wide band resolution (Z axis) | 0.006 lb RMS | 0.027 N RMS | [1] |
| Wide band resolution (X - and Y-axes) | 0.002 lb RMS | 0,0089 N RMS | [1] |
| Upper cut-off frequency | 90,000 Hz | ||
| lower limiting frequency(Z axis) (-5%) | 0.01 Hz | ||
| Lower limiting frequency (X - and Y-axes) (-5%) | 0.001 Hz | ||
| linearity | ≤ 1% FS | [4] | |
| Crosstalk (between X - and Y-axis) | ±3% | ||
| crosstalk (between X and y axis and Z axis) | ≤5% | ||
| Conditions of use | |||
| temperature range | -65 … 250 ° F | -54 … 121 ° C | |
| technical characteristics | |||
| maximum output signal (Z axis) | ± 2.5 V DC | ||
| maximum output signal (X - and Y-axes) | ±5 V DC | ||
| Discharging charging time constant (Z axis) | ≥ 50 s | ||
| discharging charging time constant (X - and Y-axes) | ≥ 500 s | ||
| Supply voltage (all axes) | 20 … 30 V DC | ||
| constant power supply (all axes) | 2 … 20 mA | ||
| Output impedance | ≤100 Ω | ||
| Bias voltage | 8 … 14 V DC | ||
| Spectral noise (X - and Y-axes) (1 Hz) | 0.0003 lb / √Hz | 0,00134 N / √Hz | |
| spectral noise (X - and Y-axes) (10 Hz) | 0.00015 lb / √Hz | 0,000668 N / √Hz | |
| spectral noise (X - and Y-axes) (100 Hz) | 0.00005 lb / √Hz | 0,000223 N / √Hz | |
| spectral noise (x and) Y-axis) (1,000 Hz) | 0,000015 lb / √Hz | 0,0000668 N / √Hz | |
| spectral noise (Z axis) (1 Hz) | 0.0015 lb / √Hz | 0,00668 N / √Hz | |
| Spectral noise (Z axis) (10 Hz) | 0,00055 lb / √Hz | 0,00245 N / √Hz | |
| spectral noise (Z axis) (100 Hz) | 0,0002 lb / √Hz | 0,000891 N / √Hz | |
| Spectral noise (Z axis) (1,000 Hz) | 0,000055 lb / √Hz | 0,000245 N / √Hz | |
| output polarity | positive | ||
| Physical properties | |||
| Preload | 5,000 lb | 22,25 kN | [5] |
| Stiffness (Z axis) | 10 lb/µin | 1.75 kN/µm | [1] |
| rigidity (X - and Y-axes) | 4 lb/µin | 0.7 kN/µm | [1] |
| Size - height | 0,390 in | 9.90 mm | |
| size - length | 1.075 in | 27.3 mm | |
| size ße - width | 0.95 in | 24.1 mm | |
| size - inner diameter | 0,319 in | 8.10 mm | |
| size - diameter of the Messoberfl surface | 0,680 in | 17,27 mm | |
| ground | 0,927 oz | 26,27 grams | |
| housing material | stainless steel | ||
| Sealing | hermetically sealed | ||
| electrical connection | 4-Pin | ||
| connection position | on the side | ||
| Notes | |||
| [1] | typically | ||
| [2] | Preload when using the recommended. The sensitivities can depending on the preload to ±5% change. | ||
| [3] | the specified sensitivities are valid only when using the supplied bolt. | ||
| [4] | zero-based balancing line, determined using the method of least squares | ||
| [5] | the preload should be at least ten times the be on the X - and Y-axis of used operating range. | ||
| [6] | details: see PCBs Declaration of conformance PS023 | ||
| equipment | |||
| 081A70 | mounting bolt | -1 | |
| 082 B 02 | washer | -1 | |
| 083A10 | mounting sleeve | -1 | |
| (W) waterproof cable connection | |||
| Cable exit | side | ||
| (M) metric mounting | |||
| equipment | |||
| M081A70 | Mounting bolt | -1 |
PCB-(M)260A01
