PCB-HT(M)628F01
    zoom_out_map

      PCB-HT(M)628F01

    • Industrial ICP® vibration sensor,
    • Continuous use temperature up to 163 ° C,
    • Measurement range 50 g,
    • Sensitivity 100 mV/g,
    • Frequency range 0.8 … 8,000 Hz,
    • Frequency response calibration,
    • 2-pin female connector above
    • ,"
      basic data
      sensitivity (±5%)100 mV/g10.2 mV/(m/s²)[7]
      measuring range±50 g±490 m / s²
      Frequency range (±5%)144 … 180,000 cpm2.4 … 3,000 Hz[2]
      frequency range (± 10%)102 … 300,000 cpm1.7 … 5,000 Hz
      frequency range (± 3 dB)48 … 480,000 cpm0.8 … 8,000 Hz
      resonance frequency1,080 kcpm18,000 Hz[1]
      wide band resolution1 mg9.8 mm / s ²[1]
      linearity≤1%[3]
      Transverse acceleration sensitivity≤ 5%
      conditions of use
      Overload limit (shock)1000 g- pk981 m/s² pk[6]
      temperature range-65 … 325 ° F-54 … 162 ° C
      Temperature range (load limit) 350° F176 ° C
      protection classIP68
      technical characteristics
      settling time (on bias voltage ± 1%)≤ 3s
      Discharging charging time constant≥ 0.2 s
      power18 … 28 V DC
      Constant power supply2 … 10 mA[4]
      output impedance< 500 Ω
      Bias voltage8 … 12 V DC
      Spectral noise (10 Hz)50 µg / √ Hz491 (µm / s ²) / √ Hz[1]
      spectral noise (100 Hz)20 µg /. √ Hz196 (µm / s ²) / √ Hz[1]
      spectral noise (1,000 Hz)6 µg / √ Hz59 (µm / s ²) / √ Hz[1]
      Electric protectionRFI/ESD
      electrical insulation (housing)≥ 100 MΩ
      Physical properties
      Size - hex7/8 in22.2 mm
      Size - height2.06 in52.3 mm
      dimensions3.2 oz91 grams
      mounting thread1/4 "-" 28 UNFNo metric equivalent[5]
      Assembly torque2 … 5 ft-lb2.7 … 6.8 Nm
      sensor elementquartz
      Geometry of the sensor elementshear principle
      housing materialstainless steel
      Sealinghermetically sealed welded
      electrical connectorMIL-C-5015
      connection positionabove
      Notes
      [1]typically
      [2]the upper cut-off frequency tolerance: ±10%
      [3]zero-based balancing line, determined using the method of least squares
      [4]At service temperature above 120 ° C there should be no larger than 6 mA of constant current.
      [5]no equivalent in SI units
      [6]particular caution when used in combination with mounting magnets required
      [7]conversion factor 1 g = 9.81 m/s²
      [8]details: see PCBs Declaration of conformance PS023
      Accessories
      081A40mounting bolts with 1/4 "-28 thread-1
      ICS-1frequency response for uniaxial sensors from 10 Hz up to the upper 5% frequency-1
      (M) metric mounting
      equipment
      M081A61metric mounting bolts with M6 thread-1
      PCB-HT(M)628F01

      Specific References

      Download

      HT628F01_drawing.PDF

      Technical drawing

      Download (34.11k)

      HT628F01_manual.PDF

      Operating instructions

      Download (794.35k)

      HT628F01_specs.PDF

      Technical data sheet

      Download (478.06k)