PCB-HT(M)602D01
| basic data | |||
| sensitivity (±10%) | 100 mV/g | 10.2 mV/(m/s²) | [1] |
| measuring range | ±50 g | ±490 m / s² | |
| Frequency range (± 10%) | 102 … 180,000 cpm | 1.7 … 3,000 Hz | [3] [4] |
| frequency range (± 3 dB) | 48 … 480,000 cpm | 0.8 … 8,000 Hz | |
| resonance frequency | 1,500 kcpm | 25,000 Hz | [2] |
| wide band resolution | 150 µg | 1.472 µm / s ² | [2] |
| Linearity | ≤1% | [5] | |
| transverse acceleration sensitivity | ≤ 5% | ||
| conditions of use | |||
| Overload limit (shock) | 5,000 g pk | 49,050 m/s² pk | |
| Temperature range | -65 … 325 ° F | -54 … 162 ° C | |
| protection class | IP68 | ||
| technical | |||
| settling time (on bias voltage±1%) | ≤ 2.0 s | ||
| discharging charging time constant | ≥ 0.2 s | ||
| power | 18 … 28 V DC | ||
| Constant power supply | 2 … 20 mA | ||
| output impedance | < 150 Ω | ||
| Bias voltage | 8 … 12 V DC | ||
| Spectral noise (10 Hz) | 9.0 µg / √ Hz | 88,3 (µm / s ²) / √ Hz | [2] |
| spectral noise (100 Hz) | 4.0 µg /. √ Hz | 39.2 (µm / s ²) / √ Hz | [2] |
| spectral noise (1,000 Hz) | 2.0 µg / √ Hz | 19.6 (µm / s ²) / √ Hz | [2] |
| Electrical insulation | ≥ 100 MΩ | ||
| Physical properties | |||
| size - length | 2.1 in | 53.3 mm | |
| size - width | 1.0 in | 25.4 mm | |
| Size - height | 1.0 in | 25.4 mm | |
| Mass | 5.4 oz | 153 grams | |
| mounting thread | 1/4"-28 | No metric equivalent | [6] |
| " Mounting torque | 2 … 5 ft-lb | 2.7 … 6.8 Nm | |
| sensor element | ceramic | ||
| geometry of the sensor element | Shear principle | ||
| housing material | stainless steel | ||
| sealing | hermetically sealed welded | ||
| Electrical connection | 2-pin connector (MIL-C-5015) | ||
| connection position | side | ||
| pin assigNment ( PIN A) | signal / supply | ||
| pin assigNment (PIN B) | dimensions | ||
| notes | |||
| [1] | conversion factor 1 g = 9.81 m/s² | ||
| [2] | typically | ||
| [3] | 1 Hz 60 = cpm ("Cycles Per Minute": rpm). | ||
| [4] | The upper cut-off frequency tolerance: ±10% | ||
| [5] | zero-based balancing line, determined using the method of least squares | ||
| [6] | mounting with M6 screw possible | ||
| [7] | details: see PCBs Declaration of conformance PS023 | ||
| equipment | |||
| 081A73 | mounting screw 1/4 "-28 x 1.34 " | -1 | |
| (M) metric mounting | |||
| equipment | |||
| M081A73 | metric mounting bolt with M6 threads | -1 |
PCB-HT(M)602D01
