PCB-113B34
zoom_out_map

PCB-113B34

  • ICP® high frequency pressure sensor with INVAR-membrane /-housing,
  • Especially insensitive to temperature transients,
  • Beschleunigungskompensiert,
  • Measuring range 6.895 kPa,
  • Sensitivity 0.73 mV / kPa,
  • Lower limiting frequency 1.0 Hz,
  • 10-32 female connector
  • of of
    basic data
    measuring range (±5 V output range) 1,000 psi 6.895 kPa
    usable range (output range ±10 V) 2,000 psi 13.790 kPa [1]
    sensitivity (±0, 25 mV / psi) 5.0 mV / psi 0.73 mV / kPa
    maximum pressure 10,000 psi 68.950 kPa
    Resolution 10 mpsi 0.069 kPa
    resonance frequency ≥ 400,000 Hz
    rise time (reflected pressure) ≤ 1.5 µs
    Lower limiting frequency1.0 Hz
    linearity ≤ 1.0% FS [2]
    conditions of use
    Acceleration sensitivity ≤ 0.002 psi/g ≤ 0,0014 kPa/(m/s²)
    temperature range (operation) -100 … 275 ° F 73 … 135 ° C
    Temperature coefficient of sensitivity ≤ 0,1 %/°F ≤ 0.18 %/°C
    maximum shock (for fraction of a second) 3,000° F 1,650 ° C
    maximum acceleration2,000 g pk 19.614 m/s 2 pk
    Maximum shock resistance 20,000 g pk 196.140 m/s² pk
    Technical properties
    Output polarity (positive pressure) positive
    Discharging charging time constant (at room temperature) 0.1 … 1,0 s
    supply 20 … 30 V DC
    Constant power supply 2 … 20 mA
    output impedance < 100 Ω
    Bias voltage 8 … 14 V DC
    Physical properties
    Geometry of the sensor element compression principle
    Sensor element quartz
    housing material INVAR
    membrane INVAR
    Sealed sealeddensely welded
    electrical connection 10-32-coaxial socket
    mass 0.2 oz 6.0 grams
    Notes
    [1] for output range supply voltage up to 10 V must be at least 24 V DC. At low bias voltage of the sensor, no negative output range is usable up to-10 V.
    [2] zero-based balancing line, determined using the method of least squares
    [3] details: see PCBs Declaration of conformance PS023
    equipment
    060A03 installation sleeve, 5/16-24-2A thread, 1/4 "hex, (stainless steel) -1
    060A05 Installation sleeve, M7 x 0.75-6 g-thread -1
    065A02 sealing ring for flush mounting, 0,248 "outside x 0.219" x 0.015 "tall, brass 3
    065A05 gasket spacer, 0,248 "outside x 0,221" x 0.240 "high, 17-4 (Stainless steel) -1
    (S) Emralon coating
    Coating Emralon
    electricIsolation ≥ 100 MΩ
    equipment
    065A08 insulation ring, 0.250 "outside x 0,218" x 0.027 "high, anodized aluminium 3
    065A22 seal, 0.250" x outside 0,218 "x 0.015", Torlon or Vespel 3
    (W) Watertight cable connection
    equipment
    060A03 installation sleeve, 5/16-24-2A thread, 1/4 "hex, (stainless steel) -1
    (WM) waterproof cable connection
    equipment
    060A05 installation sleeve, M7 x 0.75-6 g-thread -1
    PCB-113B34

    Specific References

    Download

    113B34_drawing.PDF

    Technical drawing

    Download (173.22k)

    113B34_manual.PDF

    Operating instructions

    Download (303.1k)

    113B34_specs.PDF

    Technical data sheet

    Download (31.28k)