PCB-(M)607M83
- Industrial ICP® vibration sensor
in 3- wire technology - No ICP® sensor power required
- Measuring range 45 g
- Sensitivity 100 mV / g
- Frequency range 1.5 ... 10.000 Hz
- One-point calibration at 100 Hz
- Freely orientable integrated connection cable, length 3 meters,
ending on cut end
| specifications | |||
|---|---|---|---|
| basic data | English units | SI units | |
| Sensitivity (± 20%) | 100 mV/g | 10,2 mV/(m/s²) | [1] |
| measuring range | ±45 g | ±441 m/s² | [4] |
| Frequency range (± 3 dB) | 90 … 600.000 cpm | 1,5 … 10.000 Hz | |
| resonant frequency | 1.500 kcpm | 25.000 Hz | [2] |
| Broadband resolution (1 ... 10,000 Hz) | 2 mg | 19,6 mm/s² | [2] |
| linearity error | ±1 % | [3] | |
| Lateral acceleration sensitivity | ≤7 % | ||
| Operating conditions | |||
| Overload limit (shock) | 5.000 g pk | 49.050 m/s²pk | |
| temperature range | -65 … 250 °F | -54 … 121 °C | |
| protection | IP68 | ||
| Technical characteristics | |||
| Settling time (on bias voltage ± 1%) | ≤5,0 s | ||
| discharging | ≥0,1 s | ||
| supply voltage | 3 … 12 VDC | ||
| output impedance | <100 Ω | ||
| current consumption | 0.5 mA | ||
| Bias voltage | 1,5 … 6 VDC | ||
| Spectral noise (10 Hz) | 18 µg/√Hz | 176,6 (µm/s²)/√Hz | [2] |
| Spectral noise (100 Hz) | 4 µg/√Hz | 39,2 (µm/s²)/√Hz | [2] |
| Spectral noise (1,000 Hz) | 2 µg/√Hz | 19,6 (µm/s²)/√Hz | [2] |
| Electrical insulation (housing) | >100 MΩ | ||
| Physical properties | |||
| Size - hexagon | 9/16 in | 14 mm | |
| Size - height | 0,97 in | 24,6 mm | |
| Mass (without cable) | 1,1 oz | 31 grams | [5] |
| attachment | mounting bolts | ||
| mounting thread | 1/4 "-28 male thread | no metric equivalent | [6] |
| Mounting torque (mounting bolt) | 7 … 8 ft-lb | 9,5 … 10,8 Nm | [7][8] |
| Assembly torque (hexagon union nut) | 2 … 5 ft-lb | 2,7 … 6,8 Nm | |
| sensor element | ceramics | ||
| Geometry of the sensor element | Scherprinzip | ||
| housing material | stainless steel | ||
| seal | Hermetically sealed | ||
| Electrical connection | Potted integrated cable | ||
| port location | Laterally | ||
| cable termination | Cut off end | ||
| Pin assignment (red wire) | Supply positive (+) | ||
| Pin assignment (black wire) | Mass | ||
| Pin assignment (white wire) | acceleration output | ||
| cable length | 10 ft | 3,0 m | |
| cable type | Polyurethan | ||
| Hints | |||
|---|---|---|---|
| [1] | Conversion factor 1 g = 9,81 m / s² | ||
| [2] | typically, | ||
| [3] | Zero-based balancing line, determined by the least squares method | ||
| [4] | Full measuring range only with sufficiently high supply voltage | ||
| [5] | With mounting bolts | ||
| [6] | No equivalent in SI units | ||
| [7] | Installation requires 1/8 "hex keys (for imperial mounting bolts) or 3 mm (for metric mounting bolts). | ||
| [8] | The mounting bolt must be tightened with a higher torque than the hexagon union nut, so that the sensor can be dismantled easily. | ||
| included supply | ||
|---|---|---|
| 080A156 | Mounting bolt 1/2 "-20 to 1/4" -28 | (1) |
| ICS-2 | One-point calibration at 100 Hz (traceable to NIST) | (1) |
| Available options | ||||
|---|---|---|---|---|
| (M) Metric montage | ||||
| included supply | ||||
| M080A159A | Mounting bolt 1/2 "-20 to M6 x 1 | (1) | ||
PCB-(M)607M83
