PCB-(M)642A10
- Vibration Transmitter with power output according to
the peak value of vibration speed - Measuring range 0... 12.7 mm / s,
- Output range 4... 20 mA,
- Frequency range 3... 1,000 Hz,
- Free ausrichtbares integrated cable, length 3 m,
ending on cut end
| basic data | |||
| range | 0,0... 0.5 in / s pk | 0... 25.4 mm / s pk | [1] |
| output area | 4... 20 mA | ||
| frequency range (± 10%) | 180... 60,000 cpm | 3... 1,000 Hz | [2] [3] |
| wide band resolution | 0.005 in / s RMS | 0.13 mm / s RMS | [4] |
| Linearity | ≤1% | ||
| conditions of use | |||
| temperature range | 40... 185 ° F | 40... 85 ° C | |
| specifications | |||
| power supply | 12... 30 V DC | ||
| settling time (area within ±2% of the final value) | <15 s | ||
| electric Insulation (housing) | ≥ 100 MΩ | ||
| physical properties | |||
| size - hex < / td> | 7/8 in | 22.2 mm | |
| Size - height | 1.41 in | 35.8 mm | |
| Weight (without cable) | 3.8 oz | 108 grams | |
| Mounting thread | ¾-16-Innengewinde | ||
| Installation torque | 3... 5 ft-lb | 4... 7 Nm | |
| Sensor element | Ceramic | ||
| Geometry of the sensor element | Shear principle | ||
| Housing material | Stainless steel | ||
| Sealing | Hermetically sealed welded | ||
| Electrical connection | Integrated cable | ||
| Cable outlet | On the side | ||
| Cable termination | End cut off | ||
| Terminal assigNment (red wire) | Output signal 4... 20 mA positive | ||
| Terminal assigNment (blue wire) | Output signal 4... 20 mA negative | ||
| Cable length | 10 ft | 3.0 m | |
| Cable type | Polyurethane | ||
| Notes | |||
| [1] | Conversion factor 1 in / sec = 0.0254 m/sec. | ||
| [2] | 1 Hz = cpm 60 ("Cycles Per Minute": revolutions per minute). | ||
| [3] | At frequencies below 5 Hz, the output signal fluctuates. | ||
| [4] | Typical value | ||
| [5] | Details: see PCB Declaration of conformance PS039 and PS053 | ||
| Included accessories | |||
| 080A162 | Mounting bolt ¾-16 on 1/4"-28 < " | -1 | |
| ICS-4 | Frequency response cpm for uniaxial sensors from 0 (0 Hz) up to the upper 10% frequency of vibration transmitter < /TD > | -1 | |
| (EX) With ATEX approval | |||
| Approval for explosionsgefährdete atmospheres | DIV II, CL I, GRPS A-D, ExnL, AExnA, IIC T4 | ||
| Approved for use in potentially explosive atmospheres | EEx ia IIC T4,-40 ° C?Ta?80 ° C, II 1 G | ||
| Approved for use in potentially explosive atmospheres | EEx nL IIC T4,-40 ° C?Ta?80 ° C, II 3 G | ||
| Approved for use in potentially explosive atmospheres | DIV I, CL I, II, III, GRPS A-G, ExIA, AExia, IIC T4 | ||
| (RV) Raw signal output≥ 100 MΩ/g (±20 %)<)/ b > | |||
| Electrical connection | Integrated cable | ||
| Terminal assigNment (red wire) | Output signal 4... 20 mA positive | ||
| Terminal assigNment (black wire) | Output signal 4... 20 mA negative | ||
| Terminal assigNment (white wire) | Raw signal positive | ||
| Terminal assigNment (green wire) | Raw signal negative | ||
| (M) metric mounting | |||
| Included accessories | |||
| M080A163 | Mounting bolts M6 x ¾-16 1 | -1 |
PCB-(M)642A10
