PCB-113B24
| basic data | |||
| measuring range (±5 V output range) | 1,000 psi | 6.895 kPa | |
| usable range (output range ±10 V) | 2,000 psi | 13.790 kPa | [2] |
| sensitivity (±10%) | /5.0 mV / psi | 0,725 mV / kPa | |
| maximum pressure | 10,000 psi | 68.950 kPa | |
| Resolution | 5 mpsi | 0.035 kPa | [1] |
| resonance frequency | ≥ 500, 000 Hz | ||
| rise time | ≤ 1.0 µs | ||
| Lower limiting frequency (-5%) | 0.005 Hz | ||
| linearity | ≤ 1.0% FS | [3] | |
| Conditions of use | |||
| acceleration sensitivity | ≤ 0.002 psi/g | ≤ 0,0014 kPa/(m/s²) | |
| temperature range (operation) | -100 … 275 ° F | -73 … 135 ° C | |
| Temperature coefficient of sensitivity | ≤ 0.03 %/°F | ≤ 0,054 %/°C | [1] |
| maximum shock (for Fraction of a second) | 3,000 ° F | 1.649 ° C | |
| maximum acceleration | of2,000 g pk | 19.614 m / PK | |
| Maximum shock resistance | 20,000 g pk | 196.140 m/s² pk | |
| Technical characteristics | |||
| Output polarity (positive pressure) | positive | ||
| Discharging charging time constant (at room temperature) | ≥ 100 s | ||
| supply | 20 … 30 V DC | ||
| Constant power supply | 2 … 20 mA | ||
| output impedance | < 100 Ω | ||
| Bias voltage | 8 … 14 V DC | ||
| physical properties | |||
| geometry of the sensor element | compression principle | ||
| Sensor element | quartz | ||
| goäusematerial | 17-4 (Stainless steel) | ||
| membrane | INVAR | ||
| sealing | hermetically sealed welded | ||
| Electrical connection | 10-32-coaxial socket | ||
| dimensions (with mounting sleeve) | 0.21 oz | 6.0 grams | |
| notes | |||
| [1] | typically | ||
| [2] | for output range up to 10 V the supply voltage must be at least 24 V DC amount. At low bias voltage of the sensor, no negative output range is usable up to-10 V. | ||
| [3] | zero-based balancing line, determined using the method of least squares | ||
| [4] | details: see PCBs Declaration of conformance PS023 | ||
| equipment | |||
| 060A03 | installation sleeve, 5/16-24-2A thread, 1/4 "hex, (stainless steel) | -1 | |
| 060A05 | Installation sleeve, M7 x 0,75-6 g-thread | -1 | |
| 065A02 | sealing ring for flush mounting, 0,248 "outside x 0.219" x 0.015 "high brass | 3 | |
| 065A05 | gasket spacer, 0,248" outside x 0,221 "x 0.240" high, 17-4 (Stainless steel) | -1 | |
| (S) Emralon coating | |||
| coating | Emralon | ||
| electrical insulation | ≥ 100 MΩ | ||
| Equipment | |||
| 065A08 | insulation ring, 0.250 "outside x 0,218" x 0.027 "high, anodized aluminium | 3 | |
| 065A22 | seal, 0.250 "x outside 0,218" x 0.015 "high, Torlon or Vespel | 3 | |
| (S) stainless steel diaphragm | |||
| (W) waterproof cable connection | |||
| Accessories | |||
| 060A03 | installation sleeve, 5/16-24-2A thread, 1/4 "hex, (stainless steel) | -1 | |
| (WM) waterproof cable connection | |||
| equipment | |||
| 060A05 | installation sleeve, M7 x 0.75-6 g-thread | -1 |
PCB-113B24
