PCB-3741B1230G
| basic data | |||
| sensitivity (±5%) | 66.7 mV / g | 6.80 mV/(m/s²) | [1] |
| range | ±30 g PK | ±294, 2 m/s 2 pk | |
| frequency range (±5%) | 0 … 1,000 Hz | ||
| Frequency range (±10) | 0 … 1500 Hz | ||
| resonance frequency | > 4,000 Hz | ||
| phase shift (100 Hz) | < 10 ° | ||
| Wide band resolution | 3.5 mg rms | 0.034 m/s² RMS | [2] |
| linearity error | ≤ 1% FS | [3] | |
| transverse acceleration sensitivity | ≤ 3% | ||
| conditions of use | |||
| Overload limit (shock) | ±3. 000 g pk | ±29. 420 m/s² pk | |
| temperature range (operation) | -65 … 250 ° F | -54.0 … 121 ° C | |
| Temperature range (storage) | -65 … 250 ° F | -54.0 … 121 ° C | |
| Temperature coefficient of sensitivity the zero point | ±2, 0% FSO | [4] [5] | |
| strain sensitivity (footprint) | 0.0002 g/µε | 0.002 (m/s²)/µε | [2] |
| technical characteristics | |||
| Supply voltage | 6 … 30 V DC | ||
| Power | &le≤6 mA | ||
| output impedance | ≤ 100 Ω | ||
| Spannungsoffset | ± 40 mV DC | [6] | |
| spectral noise (1) | 390 µg / √ Hz | 3,825 (µm / s ²) / √ Hz | [2] |
| electrical insulation (housing) | ≥ 100 MΩΩ | [7] | |
| physical properties | |||
| housing material | anodized aluminum | ||
| waterproofing | epoxy resin | ||
| Size-Height | 0.30 in | 7.62 mm | |
| size - length | 1.00 in | 25.4 mm | |
| size - width | 0.85 in | 21,6 mm | |
| Dimensions (without cable) | 0.35 oz | 9.92 grams | [2] |
| electrical connection | integrated cable | ||
| Cable outlet | On the side | ||
| Cable termination | tinned ends | ||
| cord type | type 010, 4-wire shielded cable | ||
| Cable length | 10 ft | 3 m | |
| Mounting | two mounting holes | ||
| notes | |||
| [1] | measured at 100 Hz, 1 g RMS | ||
| [2] | typically | ||
| [3] | zero-based balancing line, determined using the method of least squares | ||
| [4] | FSO = "Full Scale Output": maximum output signal of the measuring range (4 V DC)). | ||
| [5] | -54 … 121 ° C, reference 24 ° C | ||
| [6] | Offset tolerance for standard cable length (3 m) | ||
| [7] | between housing/cable shielding and mounting surface or wire | ||
| [8] | details: see PCB Declaration of Conformance PS027 | ||
| Optional accessory | |||
| 080A208 | triaxial mounting cube | -1 | |
| equipment | |||
| 081A103 | mounting screw | 2 | |
| ACS-103 | calibration of amplitude and phase response of 2 Hz up to the upper 5% frequency | -1 | |
| M081A103 | mounting screw and Washer, threaded M3 x 0.5 | 2 |
PCB-3741B1230G
