PCB-3711E1110G
zoom_out_map

PCB-3711E1110G

  • MEMS-DC acceleration sensor,
  • Suitable for measuring static accelerations,
  • Measuring range 10 g,
  • Sensitivity200 mV / g,
  • Typical frequency range 0 … 1,000 Hz,
  • Supply voltage 6 … 30 V DC,
  • 4-pin female connector on the side
  • basic data
    sensitivity (±5%) 200 mV / g 20.4 mV/(m/s²)
    measuring range ± 10 g ±98, 1 m/s² pk
    Frequency range (± 3 dB) 0 … 1,000 Hz [2]
    frequency range (± 3 dB) 0 … 500 Hz [3]
    Phase response < 10 °
    wide band resolution (0,5 … 100 Hz) [2] 0.002 m/s² rms rms 0.2 mg
    Linearity error ≤ 1% [1]
    transverse acceleration sensitivity ≤ 5%
    conditions
    Overload limit (Shock) ±5. 000 g pk ±49. 050 m / pk
    Temperature range (operation) -65 … 250 ° F -54 … 121 ° C
    temperature range (storage) -65 … 250 ° F -54 … 121 ° C
    Temperature coefficient of sensitivity ±3% [4]
    temperature coefficientzero ±2% FSO [4] [5]
    strain sensitivity (footprint) 0.0004 g/µε 0.004 (m/s²)/µε [2]
    Magnetic sensitivity 100 µg/Gs/9.8 (m/s²) / T [2]
    technical specifications
    power supply 6 … 30 V DC
    Power ≤ 10 mA
    output impedance ≤ 120 Ω
    Spannungsoffset ±80 mV DC [6]
    spectral noise (1 … 100 Hz) 45 µg / √ Hz 441 (µm / s ²) / √ Hz [2]
    electrical insulation (base) ≥ 100 MΩ
    physical properties
    housing material titanium
    Sealing hermetically sealed
    size - height 0.45 in 11.4 mm
    Gr öße - length 0.85in 21.6 mm
    size - width 0.85 in 21.6 mm
    mass 0.58 oz 16.3 grams
    Electrical connection 4-Pin
    Connection on the side
    mounting two mounting holes
    notes
    [1] zero-based balancing line, determined using the method of least squares
    [2] typically
    [3] guaranteed; evidenced by calibration certificate supplied with
    [4] -54 … 121 ° C, reference 24 ° C
    [5] FSO = "Full Scale Output": maximum output (4 V measuring range ( DC).
    [6] offset at 3 meters cable length (type 010)
    [7] details: see PCB Declaration of Conformance PS027
    IncludedAccessories
    080A152 mounting clip -1
    081A113 mounting screw with 4-40 thread 2
    M081A113 Mounting screw m2, 5 thread 2
    ACS-145 calibration of amplitude and phase of 2 Hz up to the upper ±3dB point (500 Hz) -1
    PCB-3711E1110G

    Specific References

    Download

    3711E1110G_drawing.PDF

    Technical drawing

    Download (200.7k)

    3711E1110G_manual.PDF

    Operating instructions

    Download (393.69k)

    3711E1110G_specs.PDF

    Technical data sheet

    Download (80.62k)