PCB-482C54

PCB-482C54

  • 4-channel power supply unit,
  • Inputs: ICP®, voltage and load,
  • Continuous gain of 0.1 … 200x,
  • BNC-inputs and outputs,
  • TEDS Support,
  • Including power supply

basic data
number channels4
sensor typeICP, voltage, charge
gain0 x to 200x
step width of the gain setting0.1
accuracy (amplification factor 0, 1 x 0, 4 x)≤5%
(amplification factor 0, 5 x to 200x) accuracy≤1%
sensitivity (±1%) (Charge input at 100 Hz)0.1 / 1.0 / 10.0 mV / pC
Insulation resistance on the Eingang(minimal erforderlich) (0.1)≥ 10 kΩhm
insulation resistance at the entrance (1.0)100 kΩ
Insulation resistance at the entrance (10.0)1 M Ω
entrance (load input, nominal)±100. 000 pC
(Minimum) output range±10 V pk
frequency range (-5%) (Amplification factor 0, 1 x 99, 9 x)0.05 … 100,000 Hz
Frequency range (-5%) (Gain 100 x to 200x)0.05 … 75,000 Hz
Lower limiting frequency (-5%) (Charge input)0.5 Hz[1]
filter type (Butterworth of fourth-order)low-pass
edge steepness of the filter24 dB/octave
Corner frequency of the electrical filter (-3 dB)10,000 Hz[2] [3]
edge steepness of the filter80 dB/decade
Frequency response accuracy in the passband of the filter0.01
attenuation in the block area of the filter (minimum)96 dB
Phase shift (at 1,000 Hz)±1 °
linearity error (load input)≤ 1% FS
crosstalk ( maximum)-72 dB
TEDS reader functionYes
display bias voltage/error (via LEDs)open circuit/short circuit /. Override
Manual
userkeypad
digital display2 lines, 16 characters
Digital interface
digital interfaceRS-232
digital interface: data rate19.200 bps
Digital interface: start, stop, parity1, 8, 1, no
digital interface: handshakeRTS/CTS
Digital interface: cable length (max)50 ft15.2 m
conditions of use
temperature range (operation)32 … 120 ° F0 … 50 ° C
Specifications
power supply (for supplied AC adaptor)AC
power supply (direct care)DC
mains voltage (50 … 60 Hz)100 … 240 V AC
AC≤ 1.6 A
Supply voltage (for sensor)≥ 24 V DC
DC Offset≤ 50 mV
DC9 … 18 V DC
DC≤ 2.5 A
Constant power supply (for sensor)0 … 20 mA[4]
output impedance≤ 50 Ω
Ü bersteuerungsschwelle (±0. 2 V pk)10 V pk
wide band noise (1 … 10,000 Hz) (amplification factor 1 x)50 µV rms[5]
Spectral noise (1 Hz) (amplification factor 1 x)8.0 µV / √ Hz[5]
Spectral noise (10 Hz) (amplification factor 1 x)1.5 µV / √ Hz[5]
spectral noise (100 Hz) (amplification factor 1 x)1.0 µV /. √ Hz[5]
spectral noise (1,000 Hz) (amplification factor 1 x)1.0 µV / √ Hz[5]
spectralNoise (10,000 Hz) (amplification factor 1 x)1.0 µV / √ Hz[5]
wide band noise (1 … 10,000 Hz) (amplification factor x 10)75 µV rms[5]
Spectral noise (1 Hz) (amplification factor x 10)20 µV / √ Hz[5]
spectral noise (10 Hz) (amplification factor x 10)1.5 µV / √ Hz[5]
spectral noise (100 Hz) (amplification factor x 10)1.0 µV / √ Hz[5]
spectral noise (1,000 Hz) (amplification factor x 10)1.0 µV / √ Hz[5]
spectral noise (10,000 Hz) (amplification factor x 10)1.0 µV / √ Hz[5]
Wide band noise (1 … 10,000 Hz) (gain 100 x)350 µV rms[5]
spectral noise (1 Hz) (gain 100 x)100,0 µ V / √ Hz[5]
spectral noise (10 Hz) (gain 100 x)10.0 µV / √ Hz[5]
spectral noise (100 Hz) (versetärkungsfaktor 100 x)8.0 µV / √ Hz[5]
spectral noise (1,000 Hz) (gain 100 x)6.0 µV / √ Hz[5]
Spectral noise (10,000 Hz) (gain 100 x)6.0 µV / √ Hz[5]
wide band noise (1 … 10,000 Hz) (0.1 mV / pC, amplification factor 1 x)52.0 µV/rms[5]
spectral noise (1 Hz) (0.1 mV / pC, amplification factor 1 x)10.0 µV / √ Hz[5]
spectral noise (10 Hz) (0.1 mV / pC, amp ärkungsfaktor 1 x)1.5 µV / √ Hz[5]
spectral noise (100 Hz) (0.1 mV / pC, amplification factor 1 x)0.6 µV / √ Hz[5]
Spectral noise (1,000 Hz) (0.1 mV / pC, amplification factor 1 x)0.6 µV / √ Hz[5]
spectral noise (10,000 Hz) (0.1 mV / pC, amplification factor 1 x)0.6 µV / √ Hz[5]
wide band noise (1 … 10,000 Hz) (1.0 mV / pC, amplification factor 1 x)52.0 µV rms[5]
Spectral noise (1 Hz) (1.0 mV / pC, amplification factor 1 x)14.0 µV / √ Hz[5]
spectral noise (10 Hz) (1.0 mV / pC, amplification factor 1 x)2.0 µV / √ Hz[5]
spectral noise (100 Hz) (1.0 mV / pC, amplification factor 1 x)0.7 µV / √ Hz[5]
spectral Noise (1,000 Hz) (1.0 mV / pC, amplification factor 1 x)0.7 µV / √ Hz[5]
spectral noise (10,000 Hz) (1.0 mV / pC, amplification factor 1 x)0.7 µV / √ Hz[5]
wide band noise (1 … 10,000 Hz) (10.0 mV / pC, amplification factor 1 x)56.0 µV rms[5]
spectral noise (1 Hz) (10.0 mV / pC, Gain 1 x)15.0 µV / √ Hz[5]
spectral noise (10 Hz) (10.0 mV / pC, amplification factor 1 x)2.0 µV / √ Hz[5]
Spectral noise (100 Hz) (10.0 mV / pC, amplification factor 1 x)0.6 µV / √ Hz[5]
spectral noise (1,000 Hz) (10.0 mV / pC, Verstärkungsfaktor 1 x)0.6 µV / √ Hz[5]
spectral noise (10,000 Hz) (10.0 mV / pC, amplification factor 1 x)0.6 µV / √ Hz[5]
Calibration input (±1%)±1. 000 pC/V
Physical properties
Electrical connection (ICP® sensor input)BNC socket
Electrical connection (load sensor input)BNC Jack
electrical connectionBNC Jack
Electrical connection (DC power supply)6-pin mini DIN socket
electrical connection (load calibration input)BNC Jack
Anschlusskonnektor (RS-232 digital interface)DB-9 connector
size - height3.2 in8.1 cm
Gr size - width8.0 in20 cm
size - deep5.9 in15 cm
dimensions2.40 lb1.089 grams
Notes
[1]the lower cut-off frequency tolerance: ±20%
[2]tolerance: ±5%
[3]more frequencies available on request
[4]Configurable, default setting at the factory: 4 mA (±1. 0 mA). The channels can individually be configured.
[5]typically
[6]details: see PCB Declaration of Conformance PS024
equipment
017AXXcord-1
100-7.103-50connection cable, length 1.8 Meters, 9-pin male to 9-pin female--1
488A14/NCpower supply-1
EE75Configuration software "MCSC"-1

1 other articles of the same category: