PCB-(M)625B10

PCB-(M)625B10

  • Industrial ICP® vibration sensor,
  • With through hole,
  • Measuring range 500 g
  • Sensitivity 10 mV / g,
  • Frequency range 0.2 … 10,500 Hz,
  • Frequency response calibration,
  • Integrated cable, length 3 m,
    ending on cut end
  • basic data
    sensitivity (±5%)10 mV / g1.0 mV/(m/s²)[6]
    measuring range≤500 Ω±4. 905 m/s 2
    Frequency range (±5%)30 … 390,000 cpm0.5 … 6,500 Hz[3]
    frequency range (± 10%)22 … 450,000 cpm0.37 … 7,500 Hz
    frequency range (± 3 dB)12 … cpm 630,0000.2 … 10,500 Hz
    resonance frequency1,500 kcpm25,000 Hz[2]
    wide band resolution350 µg3.434 µm / s ²[2]
    linearity≤1%[4]
    Transverse acceleration sensitivity≤ 5%
    conditions of use
    Overload limit (shock)5,000 g PK49,050 m/s² pk
    temperature range-65 … 250 ° F-54 … 121 ° C
    Protection classIP68
    technical Properties
    settling time (on bias voltage ± 1%)≤ 8.0 s
    discharging charging time constant≥ 1.0 s
    Supply voltage18 … 28 V DC
    constant power supply2 … 20 mA
    Output impedance< 100 Ω
    Bias voltage8 … 12 V DC
    spectral noise (10 Hz)15 µg / √ Hz147 ( µm / s ²) / √ Hz[2]
    spectral noise (100 Hz)7 µg / √ Hz69 (µm / s ²) / √ Hz[2]
    spectral noise (1,000 Hz)4 µg / √ Hz39 (µm / s ²) / √ Hz[2]
    electrical protectionRFI/ESD
    electrical insulation (housing )≥ 100 MΩ
    physical properties
    size - diameter1.38 in35.1 mm
    Size - height1.13 in28.7 mm
    dimensions (without cable)5.1 oz145 grams
    mounting Through-hole
    mounting thread1/4"-28no equivalent[5]
    Assembly torque2 … 5 ft-lb2.7 … " 6.8 Nm
    sensor elementceramic
    geometry of the sensor elementshear principle
    go äusematerialstainless steel
    sealinghermetically sealed welded
    cable length10 ft3.0 m
    Cable typepolyurethane[1]
    notes
    [1]Screened two-wire cable with twisted wire
    [2]typically
    [3]the upper cut-off frequency tolerance: ±10%
    [4]zero-based balancing line, determined using the method of least squares
    [5]Assemblyalso available with M6 screw
    [6]conversion factor 1 g = 9.81 m/s²
    Accessories
    080 B 45 Temperature protection-1
    081A73mounting screw 1/4 "-28 x 1.34"-1
    ICS-1frequency response calibration from 10 Hz up to the top 5% Frequency-1
    (M) metric mounting
    equipment
    M081A73metric mounting bolt with M6 threads-1
    (TO) temperature output
    temperature range36 … 250 ° F2 … 121 ° C
    transcription factor5.56 mV / ° F
    ( Zero point at 32 ° F)
    10 mV / ° C
    connections (red wire)acceleration output
    (black wire) pin assigNment Mass
    pin assigNment (white wire)temperature output
    pin assigNment (green wire)ground
    (LB)) Low bias voltage
    Bias voltage6 … 8 V DC
    power12 … 28 V DC
    Measuring range±350 g±3. 434 m/s²

    9 other articles of the same category: