PCB-102B11
    zoom_out_map

      PCB-102B11

      Cryogenic ICP pressure sensor, 1000 psi, 5 mV/psi, 3/8-24 mtg thd, ground isolated with lockwire hole on clamp nut and outer adaptor

      102A11 will be replaced by 102B11. It is identical description. Safety wire holes being added to the clamp nut and outer adaptor.
      • Measurement Range: 1 kpsi (6895 kPa)
      • Sensitivity: 5.0 mV/psi (0.725 mV/kPa)
      • Low Frequency Response: (-5%)0.25 Hz
      • Resonant Frequency: >=250 kHz (>=250 kHz)
      • Electrical Connector: 10-32 Coaxial Jack (10-32 Coaxial Jack)
      • Weight: .388 oz (11.00 gm)

      Specification Notes


      [1] Zero-based, least-squares, straight line method.
      [2] Due to high sensitivity, the static pressure should be applied and removed very slowly. Rate should prevent more than 10 Volt change in output until Output Bias Voltage returns to normal (approximately 15 times discharge time constant).
      [3] Excitation voltage >=28 volts required.
      [4] See PCB Declaration of Conformance PS023 for details.

      English:SI:
      Performance
      Measurement Range (for ±5V output)1 kpsi6895 kPa
      Useful Overrange (for ± 10V output)2000 psi13790 kPa [3]
      Sensitivity5.0 mV/psi0.725 mV/kPa
      Maximum Pressure (step)10000 psi69000 kPa
      Maximum Pressure (Total)15 kpsi103425 kPa [2]
      Resolution20 mpsi0.138 kPa
      Resonant Frequency≥250 kHz≥250 kHz
      Rise Time (Reflected)≤2.0 µ sec≤2.0 µ sec
      Low Frequency Response (-5 %)0.25 Hz0.25 Hz
      Non-Linearity≤1.0 % FS≤1.0 % FS [1]
      Environmental
      Acceleration Sensitivity≤0.002 psi/g≤0.0014 kPa/(m/s²)
      Temperature Range (Operating)-320 to +212 °F-196 to +100 °C
      Temperature Coefficient of Sensitivity≤0.06 %/°F≤0.108 %/°C
      Maximum Shock20000 g pk196133 m/s² pk
      Electrical
      Output Polarity (Positive Pressure)PositivePositive
      Discharge Time Constant (at room temp)≥2.0 sec≥2.0 sec
      Excitation Voltage20 to 30 VDC20 to 30 VDC
      Constant Current Excitation2 to 20 mA2 to 20 mA
      Output Impedance<100 Ohm<100 Ohm
      Output Bias Voltage9 to 13 VDC9 to 13 VDC
      Physical
      Sensing ElementQuartzQuartz
      Housing Material304L/316L Stainless Steel304L/316L Stainless Steel
      Thread Adaptor Material316L Stainless Steel316L Stainless Steel
      Diaphragm316L Stainless Steel316L Stainless Steel
      SealingWelded HermeticWelded Hermetic
      Electrical Connector10-32 Coaxial Jack10-32 Coaxial Jack
      Weight.388 oz11.00 gm

      * All specifications are at room temperature unless otherwise specified.

      Accessories


      Supplied
      065A44Seal ring, 0.435" OD x 0.377" ID x 0.030" thk, Cu (for Model 102A10)3

      Optional Versions


      (M) Metric Mount
      Accessories:
      Optional065A34Seal ring 0.435" OD x 0.397" ID x 0.030" Cu3
      PCB-102B11

      Specific References

      Download

      70414-a_drawings.pdf

      PCB-102B10_drawings

      Download (119.7k)

      102b11_specs.pdf

      PCB-102B11_specs

      Download (968.28k)

      102b11_manual.pdf

      PCB-102B11_manual

      Download (968.28k)