PCB-VO(M)625B01

PCB-VO(M)625B01

  • Industrial ICP® vibration sensor,
  • With vibration velocity output
  • With through hole,
  • Measuring range 1.27 m/s,
  • Sensitivity 3.9 mV/(mm/s),
  • Frequency range 1.5 … 6,000 Hz,
  • Frequency response calibration,
  • 2-pin female connector on the side
  • Settling time

    basic data
    sensitivity (±10%)100 mV/(in/s)3,937 mV/(m/s)[4]
     
    range±50 in / s± 1, 27 m/s 
     
    Frequency range (± 10%)180 … 150,000 cpm2.5 … 2,500 Hz[5] [6]
     
    frequency range (± 3 dB)90 … 360,000 cpm1.5 … 6,000 Hz 
     
    resonance frequency900 kcpm15,000 Hz[2]
     
    wide band resolution400 µin/s10.6 µm/s[2 ]
     
    Linearity≤1% [3]
     
    transverse acceleration sensitivity? 8%  
    Conditions of use
    5,000 g pk49,050 m/s² pkOverload limit (shock) 
     
    Temperature range-65 … 250 ° F-54 … 121 ° C 
     
    protection classIP68  
    technical
    (on bias voltage & plusmn;1%)? 30 seconds  
     
    power18 … 28 V DC  
     
    Constant power supply2 … 10 mA  
     
    output impedance< 100Ω  
     
    Bias voltage8 … 12 V DC  
     
    Spectral noise (10 Hz)25 µin/s/? Hz0.64 ?m/s/? Hz[2]
     
    spectral noise (100 Hz)3.0 µin / s /. ? Hz0.08 µm/s/? Hz[2]
     
    spectral noise (1,000 Hz)2.0 µin/s/? Hz0.05 µm/s/? Hz[2]
     
    Electric protectionRFI/ESD  
     
    electrical insulation (housing)>100 MΩ  
    physical properties
    size ße - diameter1.36 in34. 5 mm 
     
    size - height1.13 in28.7 mm 
     
    dimensions5.6 oz159 grams 
     
    Mountinghole  
     
    mounting thread1/4"-28no equivalent[1]
     
    Assembly torque "2 … 5 ft-lb2.7 … 6.8 Nm 
     
    sensor elementceramic  
     
    geometry of the sensor elementshear principle  
     
    Housing materialstainless steel  
     
    sealinghermetically sealed welded  
     
    Electrical connection2-pin connector (MIL-C-5015)  
     
    connection positionside  
    notes
    [1]Assembly with Possible M6 screw  
     
    [2]typically  
     
    [3]zero-based balancing line, determined using the method of least squares  
     
    [4]conversion factor 1 in / s = 0.0254 m/s  
     
    [5]1 Hz 60 = cpm ("Cycles Per Minute": revolutions per minute)  
     
    [6]the upper cut-off frequency tolerance: ±10%  
     
    [7]details: see PCBs Declaration of conformance PS023  
    Accessories
    080 B 45temperature protection-1 
     
    081A73mounting screw 1/4 "-28 x 1.34"-1 
     
    calibration certificate -1 
    (M) metric mounting
    Accessories supplied   
     
    M081A73metric mounting bolt with M6 thread-1 

    2 other articles of the same category: