PCB-113B34

PCB-113B34

  • ICP® high frequency pressure sensor with INVAR-membrane /-housing,
  • Especially insensitive to temperature transients,
  • Beschleunigungskompensiert,
  • Measuring range 6.895 kPa,
  • Sensitivity 0.73 mV / kPa,
  • Lower limiting frequency 1.0 Hz,
  • 10-32 female connector
  • of of
    basic data
    measuring range (±5 V output range)1,000 psi6.895 kPa
    usable range (output range ±10 V)2,000 psi13.790 kPa[1]
    sensitivity (±0, 25 mV / psi)5.0 mV / psi0.73 mV / kPa
    maximum pressure10,000 psi68.950 kPa
    Resolution10 mpsi0.069 kPa
    resonance frequency≥ 400,000 Hz
    rise time (reflected pressure)≤ 1.5 µs
    Lower limiting frequency1.0 Hz
    linearity≤ 1.0% FS[2]
    conditions of use
    Acceleration sensitivity≤ 0.002 psi/g≤ 0,0014 kPa/(m/s²)
    temperature range (operation)-100 … 275 ° F73 … 135 ° C
    Temperature coefficient of sensitivity≤ 0,1 %/°F≤ 0.18 %/°C
    maximum shock (for fraction of a second) 3,000° F1,650 ° C
    maximum acceleration2,000 g pk19.614 m/s 2 pk
    Maximum shock resistance20,000 g pk196.140 m/s² pk
    Technical properties
    Output polarity (positive pressure)positive
    Discharging charging time constant (at room temperature)0.1 … 1,0 s
    supply20 … 30 V DC
    Constant power supply2 … 20 mA
    output impedance< 100 Ω
    Bias voltage8 … 14 V DC
    Physical properties
    Geometry of the sensor elementcompression principle
    Sensor elementquartz
    housing materialINVAR
    membraneINVAR
    Sealedsealeddensely welded
    electrical connection10-32-coaxial socket
    mass0.2 oz6.0 grams
    Notes
    [1]for output range supply voltage up to 10 V must be at least 24 V DC. At low bias voltage of the sensor, no negative output range is usable up to-10 V.
    [2]zero-based balancing line, determined using the method of least squares
    [3]details: see PCBs Declaration of conformance PS023
    equipment
    060A03installation sleeve, 5/16-24-2A thread, 1/4 "hex, (stainless steel)-1
    060A05Installation sleeve, M7 x 0.75-6 g-thread-1
    065A02sealing ring for flush mounting, 0,248 "outside x 0.219" x 0.015 "tall, brass3
    065A05gasket spacer, 0,248 "outside x 0,221" x 0.240 "high, 17-4 (Stainless steel)-1
    (S) Emralon coating
    CoatingEmralon
    electricIsolation≥ 100 MΩ
    equipment
    065A08insulation ring, 0.250 "outside x 0,218" x 0.027 "high, anodized aluminium3
    065A22seal, 0.250" x outside 0,218 "x 0.015", Torlon or Vespel3
    (W) Watertight cable connection
    equipment
    060A03installation sleeve, 5/16-24-2A thread, 1/4 "hex, (stainless steel)-1
    (WM) waterproof cable connection
    equipment
    060A05installation sleeve, M7 x 0.75-6 g-thread-1

    30 other articles of the same category: