PCB-HT(M)622A01
    zoom_out_map

      PCB-HT(M)622A01

    • Industrial ICP® vibration sensor,
    • Continuous use temperature up to 163 ° C,
    • Measurement range 50 g,
    • Sensitivity 100 mV/g,
    • Frequency range 0.2 … 8,000 Hz,
    • Frequency response calibration,
    • 2-pin female connector above
    • ",
      basic data
      sensitivity (±5%)100 mV/g10.2 mV/(m/s²)[1]
      measuring range±50 g±490 m / s²
      Frequency range (±5%)35 … 240,000 cpm0.58 … 4,000 Hz[7] [8]
      frequency range (± 10%)25 … 300,000 cpm 0.42 … 5,000 Hz
      frequency range (± 3 dB)12 … 480,000 cpm0.2 … 8,000 Hz
      resonance frequency1.200 kcpm 20,000 Hz[2]
      wide band resolution150 µg1.472 µm / s ²[2]
      linearity≤1%[3]
      Transverse acceleration sensitivity≤ 5%
      conditions of use
      Overload limit (shock)5,000 g PK49,050 m/s² pk
      Temperature range-65 … 325 ° F-54 … 163 ° C
      technical
      settling time(on bias voltage ± 1%)≤<5 s
      Discharging charging time constant≥ 0.8 s
      power18 … 28 V DC
      Constant power supply2 … 10 mA[4]
      output impedance< 700 Ω
      Bias voltage (at 4 mA)8 … 15 V DC[5]
      spectral noise (10 Hz)12 µg / √ Hz118 (µm / s ²) / √ Hz[2]
      spectral noise (100 Hz)3.2 µg /. √ Hz31.4 (µm / s ²) / √ Hz[2]
      spectral noise (1,000 Hz)1.2 µg / √ Hz11.8 (µm / s ²) / √ Hz[2]
      Electrical protectionRFI/ESD
      Electrical insulation≥ 100 MΩ
      physical properties
      size - hex7/8 in22.2 mm
      Size - height2.0 in50.8 mm
      mass3.3 oz93 grams
      mounting thread1/4 "-28 UNFno equivalent[6]
      Assembly torque2 … 5 ft-lb2.7 … 6.8 Nm
      sensor elementceramic
      geometry of the Sensor elementshear principle
      housing materialstainless steel
      sealinghermetically sealed welded
      Electrical connectorMIL-C-5015
      connection positionabove
      notes
      [1]Conversion factor 1 g = 9.81 m/s²
      [2]typically
      [3]zero-based balancing line, determined using the method of least squares
      [4]maximum 4 mA recommended at temperatures above 121 ° C
      [5]at larger constant current, the bias voltage increases.
      [6]noEquivalent in SI units
      [7]1 Hz 60 = cpm ("Cycles Per Minute": rpm).
      [8]the upper cut-off frequency tolerance: ±10%
      [9]details: see PCBs Declaration of conformance PS023
      Accessories
      081A40mounting bolts with 1/4 "-28 thread-1
      ICS-1frequency response for uniaxial sensors from 10 Hz up to" to the upper 5% frequency-1
      (M) metric mounting
      equipment
      M081A61metric mounting bolts with M6-thread-1
      (TO) temperature output
      temperature range36 … 302 ° F2 … 150 ° C
      transcription factor5.56 mV / ° F
      (zero point at 32 °F)
      10 mV / ° C
      Electrical connection3-Pin
      pin assigNment (PIN A)acceleration output
      pin assigNment (PIN B)Mass
      Terminal assigNment (PIN C)Temperature output
      PCB-HT(M)622A01

      Specific References

      Download

      HT622A01_manual.PDF

      Operating instructions

      Download (855.37k)

      HT622A01_specs.PDF

      Technical data sheet

      Download (62.2k)