This website uses cookies, which are necessary for the technical operation of the site and which are always set. In order to further improve our offer and our website, we would like to set additional cookies in order to collect anonymized data for statistics and analyzes. However, these are only set with your consent. Further information on cookies can be found in our privacy policy.

Privacy policy Acceptdone
    PCB-(M)602D91
    zoom_out_map

      PCB-(M)602D91

    • Industrial ICP® vibration sensor,
    • With through hole,
    • Measurement range 50 g,
    • Sensitivity 100 mV/g,
    • Frequency range 0.5 … 8,000 Hz,
    • One-point calibration at 100 Hz,
    • M12 connector on the side
      • "
      basic data
      sensitivity (±10%)100 mV/g10.2 mV/(m/s²)[1]
      measuring range±50 g±490 m / s²
      Frequency range (± 3 dB)30 … 480,000 cpm0.5 … 8,000 Hz[4]
      resonance frequency1,500 kcpm25,000 Hz[2]
      Wide band resolution350 µg3.434 µm / s ²[2]
      linearity≤1%[3]
      Transverse acceleration sensitivity≤ 7%
      conditions of use
      (shock) overload limit49,050 m/s ² pkpk 5,000 g
      Temperature range-65 … 250 ° F-54 … 121 ° C
      temperature impact on Temperature coefficient of sensitivitysee curve below[2]
      Protection classIP68
      technical characteristics
      settling time (on area within ±1% of the bias voltage)≤ 3.0 s
      Discharging charging time constant≥ 0.3s
      power18 … 28 V DC
      constant power supply2 … 20 mA
      output impedance< 150 Ω
      Bias voltage8 … 12V DC
      Spectral noise (10 Hz)8.0 µg / √ Hz78.5 (µm / s ²) / √ Hz[2]
      spectral noise (100 Hz)5 µg / √ Hz49,1 (µm / s ²) / √ Hz[2]
      spectral noise (1,000 Hz)4 µg / √ Hz39.2 (µm / s ²) / √ Hz[2]
      Electrical insulation≥ 100 MΩ
      physical properties
      size - length1.55 in39.4 mm
      Size - width0.74 in18.8 mm
      Size - height0,845 in21.5 mm
      mass2.61 oz74.0 grams
      Mounting thread1/4 "-28 threadNo metric equivalent[5]
      Assembly torque2 … 5 ft-lb2.7 … 6.8 Nm
      Sensor elementceramic
      geometry of the sensor elementshear principle
      housing materialStainless steel (316 L)
      Sealinghermetically sealed welded
      connectionon the side
      notes
      [1]conversion factor 1 g = 9.81 m/s²
      [2]typically
      [3]zero-based balancing line,. determined with the method of least squares
      [4]the upper cut-off frequency tolerance: ±10%
      [5]no equivalent in SI
      [6]details: see PCBs Declaration of conformance PS023
      equipment
      081A97 Transit bolt 1 /.4 ' 28-1
      ICS-2single point calibration at 100 Hz (traceable to NIST)-1
      (M) metric mounting
      supplied accessories " ör
      M081A97metric mounting bolt with M6 thread-1
      PCB-(M)602D91

      Specific References

      Download

      602D91_drawing.PDF

      Technical drawing

      Download (97.96k)

      602D91_manual.PDF

      Operating instructions

      Download (927.91k)

      602D91_specs.PDF

      Technical data sheet

      Download (75.26k)