PCB-(M)607A12

PCB-(M)607A12

  • Industrial ICP® vibration sensor,
  • Measuring range 10 g,
  • Sensitivity500 mV / g,
  • Frequency range 0.5 … 3,000 Hz,
  • One-point calibration at 100 Hz,
  • Free ausrichtbares integrated cable, length 3 m,
    ending on cut end
  • basic data
    sensitivity (±20%)500 mV / g51.0 mV/(m/s²)[7]
    measuring range± 10 g±98 m / s²
    Frequency range (± 3 dB)30 … 180,000 cpm0.5 … 3,000 Hz[1]
    resonance frequency1,500 kcpm25,000 Hz[3]
    Wide band resolution300 µg2.943 µm / s ²[3]
    linearity≤1%[4]
    Transverse acceleration sensitivity≤ 7%
    conditions of use
    Overload limit (shock)5,000 g pk49,050 m/s² pk
    temperature range-65 …200 °F-54 … 93 ° C
    Type of protectionIP68
    Technical characteristics
    settling time (on bias voltage ± 1%)≤ 5.0 s
    discharging charging time constant≥ 0.3 s
    Power18 … 28 V DC
    constant power supply2 … 20 mA
    Output impedance< 500 Ω
    Bias voltage8 … 12 V DC
    Spectral noise (10 Hz)8 µg / √ Hz78.5 (µm / s ²) / √ Hz[3]
    spectral noise (100 Hz)3 µg / √ Hz 29.4 (µm / s ²) / √ Hz[3]
    spectral noise (1,000 Hz)3 µg / √ Hz29.4 (µm / s ²) / √ Hz[3]
    electric Insulation (housing)≥ 100 MΩ
    physical properties
    size - Allen9/16 in14 mm
    size ße - height0.97 in24.6 mm
    weight1.1 oz31 grams[3]
    fixingmounting bolt
    Assembly torque(Mounting bolts)7 … 8 ft-lb9.5 … 10.8 Nm[5] [6]
    Assembly torque (hex nut)2 … 5 ft-lb2.7 … 6.8 Nm
    sensor elementceramic
    Geometry of the sensor elementshear principle
    housing materialstainless steel
    sealinghermetically sealed welded
    electrical connectionpotted integrated cable
    cable exitside
    Cable terminationcut end
    cable length10 ft3.0 m
    cable typepolyurethane[2]
    notes
    [1]the upper cut-off frequency tolerance: ±10%
    [2]shielded two-wire cable with twisted pair wires
    [3]typically
    [4]zero-based balancing line, determinedusing the method of least squares
    [5]Assembly requires Allen key 1/8 "(for inch mounting bolts) or 3 mm (for metric mounting bolts).
    [6]of the mounting bolts must be tightened with a higher torque than the hex nut, so that the sensor can easily be removed.
    [7]conversion factor 1 g = 9.81 m/s²
    [8]details: see PCBs Declaration of conformance PS023
    Accessories supplied
    080A156mounting bolts 1/2 "-20 1/4" 28-1
    ICS-2single point calibration at 100 Hz (traceable to NIST)-1
    (M) metric mounting
    equipment
    M080A159Amounting bolts 1/2 "20 M6 x 1-1
    (EX) ATEX approved
    "

    15 other articles of the same category: